Cart
*system recommended video (beta)

Moog Modular System 35 Synthesizer

Sold/Fulfilled by Simba Pte Ltd
Moog, MOD-SYS-35-01-01, Moog Modular System 35 Synthesizer - Recreated from the1973 Factory Specs. 22 Hand-Made...
In stock *In Stock - Subject to stock availability at point of fulfilment. In the event whereby the item is out of stock or unable to supply, the order would be cancelled and a full refund will be made to the customer.
SKU 6qPTZWhiXgE4o2yeOmYuAO

Free Shipping Worldwide available. Shipping time may vary depending on the address.

**Our CoVid-19 Message - This is a time of great stress and uncertainty. We are activelly validating, routing and re-routing orders with our overseas merchants, logistic partners and airlines. Deliveries and supply may expect delays. (*Important: See DHL Service Alert)

**In Stock (Low Inventory Warning) - Subject to stock availability at point of fulfilment. In the event whereby the item is out of stock or unable to supply, the order would be cancelled and a full refund will be made to the customer.

Products may be shipped or fulfilled from overseas principals, merchants, warehouses, or local suppliers. (e.g. USA, UK, Dubai, Singapore, China, etc).

Have one to sell? Cheaper or better? Sell and Export your products to 250,000 visitors daily Worldwide, within 24 hours.

Report any copyrighted, inappropriate, offensive, prohibited, potentially Illegal Listings.



Moog modular system 35 synthesizer,MOD-SYS-35-01-01 - Both fixed and variable levels can be obtained from face panel output jacks. The Frequency pot at the top of the module has a two-octave range for fine-tuning, while the Range switch shifts the frequency of the oscillator in octaves, up or down. Includes Patch and Trigger Cables

The White and Pink noise outputs of the 923 Random Noise/Filter module produce continuous bursts of random frequencies and waveshapes throughout the audio spectrum. The two manual sweep filters, Low-Pass and High-Pass, are single-pole {RC} circuits with a frequency cutoff slope of 6 dB per octave.; The Frequency Range switch sets the overall range of frequencies covered by the Fixed Control Potential potentiometer.

Four waveforms are available: Sine, Triangular, Sawtooth, and Rectangular {with variable duty cycle}. As the fundamental is generally the loudest frequency component of a complex tone, deletion of the lowest frequency range can radically alter the timbre. A resultant lower frequency concentration for Pink Noise marks the difference between the two outputs, with white noise appearing in even intensity throughout the audio spectrum.

The CP3A module has four varied functions. Two voltages are generated: one for frequency control and one for rectangular wave duty cycle. At the introduction of a switch-to-ground {S-trigger} trigger signal from an external source, the 911 Envelope Generator produces a single voltage contour whose time/voltage variation is determined by potentiometers T1, T2, T3, and a time-constant sustaining level pot {Esus}.

They are wired in groups to a common 921A Oscillator Driver, which provides both exponential frequency control and rectangular width voltage control.; Maximum sum of control voltage {fixed control voltage and input jacks} is approximately 7.5 control volts, producing +4.7 dB or gain of 3. They are wired in groups to a common 921A Oscillator Driver, which provides both exponential frequency control and rectangular width voltage control.Like the 921 Oscillator, this is one of the building blocks of analog synthesis.

The second series of functions are four signal routing switches, which colligate the incoming control voltages from keyboard, ribbon or other controller units to the frequency control input of associated oscillator drivers found directly above the switching panel. 1 x 923 Random Noise/Filter; This oscillator generates both sub-audio and audio frequencies for control and audio signal use.

Potential controlled rectangular width is set by the knob in the upper center {left}, with accompanying voltage input jacks. The regeneration potentiometer {variable Q} varies the amount of internal feedback, creating a resonant peak at the cutoff frequency. At "10" a signal introduced here make up one's mind be equal to one which is introduced directly into the frequency control inputs found on the Oscillator Driver itself.

Number indications on the Range switch correspond to traditional organ pipe range notations. The two manual sweep filters, Low-Pass and High-Pass, are single-pole {RC} circuits with a frequency cutoff slope of 6 dB per octave.; The Envelope Generator requires an S-trigger to operate.

The overall range of the FCV pot is determined by the Frequency Range switch, which moves the frequency cutoff range in two-octave steps.The basic cutoff frequency of the Low-Pass Filter is determined by the combination of fixed control voltage and frequency range in addition to the control input signals. The attenuation below FCV cutoff setting is 24dB/oct. An increase in regeneration narrows and increases the strength of the cutoff frequency peak, while decreasing the amplitude of the lower frequencies.;

Nominal frequency is set manually by the scale, coarse range, frequency and {octave} range controls found at the top of the module. An increase in regeneration narrows and increases the strength of the cutoff frequency peak, while decreasing the amplitude of the lower frequencies.; 5-Oscillator Instrument;

Control inputs for frequency and rectangular width are summing.; The CP3A module has four varied functions. The 904B Potential-Controlled High-Pass Filter attenuates input signal frequencies below its nominal cutoff frequency setting.

A sawtooth waveform is recommended for best synchronization results.; Phase locking capability is generally limited to the first six harmonics of the input signal. Manual adjustment to the Frequency and Width Of Rectangular Wave pots changes the nominal frequency and duty cycle of all colligateed 921B's in parallel.

Fixed level outputs for Sine, Triangle, Sawtooth and Rectangular waveforms are found at the right of the modules. Potential controlled rectangular width is set by the knob in the upper center {left}, with accompanying voltage input jacks. The 921B Oscillator generates frequencies from 1 Hz to 40 kHz minimum.

The overall range of the FCV pot is determined by the Frequency Range switch, which moves the frequency cutoff range in two-octave steps.; Multiple frequency control inputs can be plugged into this module in parallel. The two final elements found on the CP3A are a multiple {signal splitting - one input becomes three} and trunk line jacks, which carry a signal to the rear of the synthesizer.;

The primary circuit is a 4x1 mixer with positive and negative outputs and a maximum gain of 2x. The attenuation below FCV cutoff setting is 24dB/oct. The 907A Fixed Filter Bank is a non-voltage-controlled modifier, which emphasizes or reduces the gain of the center frequency bands indicated on each of the eight center pots, in addition to the cutoff points set by low-pass and high pass-filters at either frequency extreme.

Clamping point {waveform reset control} may be set with the lower left knob and accompanying trigger inputs to the left. The regeneration potentiometer {variable Q} varies the amount of internal feedback, creating a resonant peak at the cutoff frequency. Pink noise displays equal amplitude/energy per octave.

Nominal frequency is set manually by the scale, coarse range, frequency and {octave} range controls found at the top of the module. All waveform outputs can be used concurrently if desired.; A total of 10 overlapping LC networks are included.;

The second series of functions are four signal routing switches, which colligate the incoming control voltages from keyboard, ribbon or other controller units to the frequency control input of associated oscillator drivers found directly above the switching panel. The 904A Low-Pass Filter attenuates frequencies above the fixed control-voltage cutoff point at a rate of 24 dB per octave. DC Modulate is a linear frequency control input {does not conform to 1 volt/octave control voltage format}.

The 904A Low-Pass Filter attenuates frequencies above the fixed control-voltage cutoff point at a rate of 24 dB per octave. The FCV cutoff point is raised or lowered in octave-per-volt control inputs.The Frequency Range switch sets the overall range of frequencies covered by the Fixed Control Potential potentiometer. The 921 Potential-Controlled Oscillator is a variable waveform generator, which produces frequencies ranging from .01 Hz to 40 kHz.

3 x 902 Potential-Controlled Amplifiers1 x 904A Potential-Controlled Low-Pass Filter1 x 904B Potential-Controlled High-Pass Filter1 x 907A Fixed Filter Bank3 x 911 Envelope Generators1 x 921 Potential-Controlled Oscillator2 x 921A Oscillator drivers4 x 921B Oscillators1 x 923 Random Noise/Filter2 x CP3A Console Panels1 x CP4A Console Panel1 x CP8A Console Panel1 x CP35 Console Panel1 x 180 Watt 120 VAC or 230 VAC Switch Selectable Power Supply; AC Modulate input is a capacitor-coupled circuit like the DC Modulate input, however, blocking constant DC voltages.; Control inputs for frequency and rectangular width are summing.;

Phase locking capability is generally limited to the first six harmonics of the input signal. All manual controls on this module can be moved or switched during operation. Multiple frequency control inputs can be plugged into this module in parallel.

The 907A Fixed Filter Bank is a non-voltage-controlled modifier, which emphasizes or reduces the gain of the center frequency bands indicated on each of the eight center pots, in addition to the cutoff points set by low-pass and high pass-filters at either frequency extreme. The primary circuit is a 4x1 mixer with positive and negative outputs and a maximum gain of 2x. Maximum sum of control voltage {fixed control voltage and input jacks} is approximately 7.5 control volts, producing +4.7 dB or gain of 3.

A total of 10 overlapping LC networks are included.; Clamping point {waveform reset control} may be set with the lower left knob and accompanying trigger inputs to the left. A sawtooth waveform is recommended for best synchronization results.;

Custom Hand-Finished Walnut Cabinet; This input jack is colligateed to the Oscillator Driver when the associated switch is on and the attenuator set above zero. The 921A Oscillator Driver is a control-voltage processor, which drives associated 921B oscillators through internally wired colligateions {via edge colligateors}.

1 x CP4A Console Panel; Two modes of gain response are available: linear and exponential.; Two modes of gain response are available: linear and exponential.;

Recreated from the1973 Factory Specs; At "10" a signal introduced here make up one's mind be equal to one which is introduced directly into the frequency control inputs found on the Oscillator Driver itself. Parallel outputs are provided for both noise sources.

The Frequency pot at the top of the module has a two-octave range for fine-tuning, while the Range switch shifts the frequency of the oscillator in octaves, up or down. Parallel outputs are provided for both noise sources. The 921A Oscillator Driver is a control-voltage processor, which drives associated 921B oscillators through internally wired colligateions {via edge colligateors}.

1 x 921 Potential-Controlled Oscillator; The 902 Potential-Controlled Amplifier is a differential input and output circuit which gives an overall voltage gain of 2 {6dB} when the manual control potentiometer is at maximum {6}, or when a control voltage of 6 volts is applied to the control input. This module functions as both an audio or control-voltage generator.;

The White and Pink noise outputs of the 923 Random Noise/Filter module produce continuous bursts of random frequencies and waveshapes throughout the audio spectrum. Pink noise displays equal amplitude/energy per octave. A resultant lower frequency concentration for Pink Noise marks the difference between the two outputs, with white noise appearing in even intensity throughout the audio spectrum.

This module functions as both an audio or control-voltage generator.; Control inputs to this module change the frequency of its associated oscillators in volt/octave increments. The cutoff point {cutoff frequency} is voltage-controlled through the control input jacks.

Closure of the input trigger switch directs the voltage contour to T3 {final decay} regardless of what stage { T1, T2 or E} was in current operation. All waveform outputs can be used concurrently if desired.All manual controls on this module can be moved or switched during operation. Like the 921 Oscillator, this is one of the building blocks of analog synthesis.

The basic cutoff frequency of the Low-Pass Filter is determined by the combination of fixed control voltage and frequency range in addition to the control input signals. 3 x 902 Potential-Controlled Amplifiers; The fourth input switch has both an external input jack and attenuator {found directly below}.

The cutoff point {cutoff frequency} is voltage-controlled through the control input jacks. This input jack is colligateed to the Oscillator Driver when the associated switch is on and the attenuator set above zero. External sources must be converted to the S-trigger format via the 961 Interface.;

AC Modulate input is a capacitor-coupled circuit like the DC Modulate input, however, blocking constant DC voltages.921B Oscillators may be phase locked together via the Synch input jack and the associated three position Synch Switch. The sum of the applied control voltages doubles the frequency of the cutoff point for each one-volt increase {volt per octave standardization}. 4 x 921B Oscillators;

The Low range encompasses 4 Hz to 20 kHz, while the High range shifts 1 1/2 octaves up from 10 Hz through 50 kHz.; The fourth input switch has both an external input jack and attenuator {found directly below}. At the introduction of a switch-to-ground {S-trigger} trigger signal from an external source, the 911 Envelope Generator produces a single voltage contour whose time/voltage variation is determined by potentiometers T1, T2, T3, and a time-constant sustaining level pot {Esus}.

The 921B Oscillator generates frequencies from 1 Hz to 40 kHz minimum. Number indications on the Range switch correspond to traditional organ pipe range notations. 1 x 904B Potential-Controlled High-Pass Filter;

DC Modulate is a linear frequency control input {does not conform to 1 volt/octave control voltage format}. The FCV cutoff point is raised or lowered in octave-per-volt control inputs.; 2 x 921A Oscillator drivers;

1 x 907A Fixed Filter Bank; Manual adjustment to the Frequency and Width Of Rectangular Wave pots changes the nominal frequency and duty cycle of all colligateed 921B's in parallel. Both fixed and variable levels can be obtained from face panel output jacks.

This mixer can combine both AC and/or DC voltages. External sources must be converted to the S-trigger format via the 961 Interface.; Two ranges are provided on the Frequency potentiometer: semitone {two octaves compass} and octave {12 octaves compass} These ranges are selected by the white switch below the Frequency potentiometer.

Two voltages are generated: one for frequency control and one for rectangular wave duty cycle. The two final elements found on the CP3A are a multiple {signal splitting - one input becomes three} and trunk line jacks, which carry a signal to the rear of the synthesizer.; This oscillator generates both sub-audio and audio frequencies for control and audio signal use.

The Envelope Generator requires an S-trigger to operate. 1 x CP35 Console Panel; As the fundamental is generally the loudest frequency component of a complex tone, deletion of the lowest frequency range can radically alter the timbre.

This resonant peak make up one's mind break into oscillation at clockwise settings of the regeneration pot, creating a voltage-controlled sine wave generator. 2 x CP3A Console Panels; The fixed control-voltage pot covers a 12-volt {octave} range.

3 x 911 Envelope Generators; Closure of the input trigger switch directs the voltage contour to T3 {final decay} regardless of what stage { T1, T2 or E} was in current operation. 1 x 904A Potential-Controlled Low-Pass Filter;

Four waveforms are available: Sine, Triangular, Sawtooth, and Rectangular {with variable duty cycle}. 1 x CP8A Console Panel; 921B Oscillators may be phase locked together via the Synch input jack and the associated three position Synch Switch.

22 Hand-Made Modules; Two ranges are provided on the Frequency potentiometer: semitone {two octaves compass} and octave {12 octaves compass} These ranges are selected by the white switch below the Frequency potentiometer. This resonant peak make up one's mind break into oscillation at clockwise settings of the regeneration pot, creating a voltage-controlled sine wave generator.

Fixed level outputs for Sine, Triangle, Sawtooth and Rectangular waveforms are found at the right of the modules. The 921 Potential-Controlled Oscillator is a variable waveform generator, which produces frequencies ranging from .01 Hz to 40 kHz. The Low range encompasses 4 Hz to 20 kHz, while the High range shifts 1 1/2 octaves up from 10 Hz through 50 kHz.;

This mixer can combine both AC and/or DC voltages. The 902 Potential-Controlled Amplifier is a differential input and output circuit which gives an overall voltage gain of 2 {6dB} when the manual control potentiometer is at maximum {6}, or when a control voltage of 6 volts is applied to the control input. The 904B Potential-Controlled High-Pass Filter attenuates input signal frequencies below its nominal cutoff frequency setting.

1 x 180 Watt 120 VAC or 230 VAC Switch Selectable Power Supply; Control inputs to this module change the frequency of its associated oscillators in volt/octave increments. The fixed control-voltage pot covers a 12-volt {octave} range.

The sum of the applied control voltages doubles the frequency of the cutoff point for each one-volt increase {volt per octave standardization}.


SKU

6qPTZWhiXgE4o2yeOmYuAO

Model

MOD-SYS-35-01-01

Brand

Moog

Weight Product (Kg)

0.454

MPN

MOD-SYS-35-01-01

SKU

6qPTZWhiXgE4o2yeOmYuAO

Model

MOD-SYS-35-01-01

Brand

Moog

Weight Product (Kg)

0.454

MPN

MOD-SYS-35-01-01
TERMS AND WARNING

 

TERMS OF USE

Please refer to Our Terms of Use and Privacy Policy Page.

By using this website you are agreeing to be bound by the then-current version of these Terms.

 

CANCELLATION AND REFUND POLICY

You may cancel your order for a refund if you’ve placed the order within 24 hours. The refund will be credited to the same credit/debit card facility, and currency transacted.

To qualify for a refund, you must cancel your order before order confirmation, in writing. We will also absorb all the transactional, commission fees and charges.

In the event whereby the customs declaration and import are not successful, you would also be refunded in full.

No cancellation or refunds after the order have been confirmed or ship out by our merchants.

 

**HAZARD AND LEGAL PRECAUTION

Product may not be tested, safe, compatible or approved for your country.  Please check with your local law enforcer.

 

**TELECOMMUNICATION EQUIPMENT

Products operating in the GSM Frequency Bands (890-915 MHz and 935-960 MHz), may not be registered, it is “For Export Only – Not Approved for local use".

Otherwise, a permit (e.g. IDA permit) or valid approval number must be provided.

 

**HEALTH PRODUCTS

Product may be unreliable. Health products should be imported or sold stringently for export, non-clinical, clinical trial and/or personal use only.

Product quantities should not exceed 3 month's supply per shipment. Otherwise, a  valid medical device registration number or valid approval number must be provided (e.g. HSA).

Disclaimer: Never use health products, without a Qualified Person (QP) or Doctor. Failure to do so can result in death or serious injuries. 

 

WARRANTY

Products come with a limited warranty covering manufacturing defects, up to 30 days. 

Electrical products do not come with any warranty, please contact manufacturers directly for manufacturer warranty.

 

[Re: Terms and Warning.]